ABBIndustrialIT Panel 800 - PP865 Version 5.1 Hardware and Installation

DE DECONNECTER L’EQUIPEMENT, COUPER LE COURANT 

OUS’ASSURER QUE L‘EMPLACEMENT EST DESIGNE NON 

DANGEREUX.

• WARNING – EXPLOSION HAZARD - Substitution of components may 

impair suitability for Class I, Division 2.

• For Canada also AVERTISSEMENT – RISQUE D’EXPLOSION – LA 

SUBSTITUTION DE COMPOSANTS PEUT RENDRE CE MATERIEL 

INACCEPTABLE POUR LES EMPLACEMENTS DE CLASSE I, DIVISION 

2.

• WARNING – EXPLOSION HAZARD – only UL and cUL approved 

expansion units are allowed to be connected to the port designated 

“EXPANSION”. At the moment there are no such units evaluated or allowed.

• WARNING – EXPLOSION HAZARD - Do not replace expansion unit unless 

power has been switched off or the area is known to be non-hazardous.

• This product contains battery, this must only be changed in an area known to be 

non-hazardous. Permitted types are shown in the Section 4, Technical Data.

• For use on a flat surface of a type 4X enclosure indoor use only.

• To make wiring connections to the power supply connector, use an AWG 28-12 

cable and a tightening torque of min. 0.5 Nm.

General

• Read the safety precautions carefully.

• Check the delivery for transportation damage. If damage is found, notify the 

supplier as soon as possible.

• Do not use the operator panel in an environment with high explosive hazards.

• The supplier is not responsible for modified, altered or reconstructed 

equipment.

• Use only parts and accessories manufactured according to specifications of the 

supplier.

• Read the installation and operating instructions carefully before installing, 

using or repairing the operator panel.

• Never allow fluids, metal filings or wiring debris to enter any openings in the 

operator panel. This may cause fire or electrical shock.

• Only qualified personnel may operate the operator panel.

• Storing the operator panel where the temperature is lower/higher than 

recommended in this manual can cause the LCD display liquid to 

congeal/become isotopic.

• The LCD display liquid contains a powerful irritant. In case of skin contact, 

wash immediately with plenty of water. In case of eye contact, hold the eye 

open, flush with plenty of water and get medical attention.

• The figures in this manual serves an illustrative purpose. Because of the many 

variables associated with any particular installation, the supplier cannot assume 

responsibility for actual use based on the figures.

• The supplier neither guarantees that the operator panel is suitable for your 

particular application, nor assumes responsibility for your product design, 

installation or operation.

During Installation

• The operator panel is designed for stationary installation on a plane surface, 

where the following conditions are fulfilled:

– no high explosive risks.

– no strong magnetic fields.

– no direct sunlight.

– no large, sudden temperature changes.

• Install the product according to the accompanying installation instructions.

• Ground the product according to the accompanying installation instructions.

• Only qualified personnel may install the operator panel.

• Separate the high voltage, signal and supply cables.

• Make sure that the voltage and polarity of the power source is correct before 

connecting the product to the power outlet.

• Peripheral equipment must be appropriate for the application and location.

During Use

• Keep the operator panel clean.

• Emergency stop and other safety functions may not be controlled from the 

operator panel.

• Do not use too much force or sharp objects when touching the keys, display 

etc.

Service and Maintenance

• Only qualified personnel should carry out repairs.

• The agreed warranty applies.

• Before carrying out any cleaning or maintenance operations, disconnect the 

equipment from the electrical supply.

• Clean the display and surrounding front cover with a soft cloth and mild 

detergent.

• Replacing the battery incorrectly may result in explosion. Only use batteries 

recommended by the supplier. 

Dismantling and Scrapping

• The operator panel or parts thereof shall be recycled according to local 

regulations.

• The following components contain substances that might be hazardous to 

health and the environment: lithium battery, electrolytic capacitor and display.

Section 3 Installation

Space Requirements

• Installation plate thickness: 1.5 - 9.0 mm (0.06 - 0.35 inch)

• Space requirements when installing the operator panel:

The openings on the enclosure are for air convection. Do not cover these 

openings.