schneiderSun™ StorEdge™ UniPack User’s Guide

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own

expense.

Shielded Cables: Connections between the workstation and peripherals must be made using shielded cables in order to maintain

compliance with FCC radio frequency emission limits. Networking connections can be made using unshielded twisted-pair (UTP)

cables.

Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the authority

granted to the user by the FCC to operate this equipment.

FCC Class B Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Shielded Cables: Connections between the workstation and peripherals must be made using shielded cables in order to maintain

compliance with FCC radio frequency emission limits. Networking connections can be made using unshielded twisted pair (UTP)

cables.

Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the authority

granted to the user by the FCC to operate this equipment.

DOC Class A Notice - Avis DOC, Classe A

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

DOC Class B Notice - Avis DOC, Classe B

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada

Safety Agency Compliance Statements

Read this section before beginning any procedure. The

following text provides safety precautions to follow when

installing a Sun Microsystems product.

Safety Precautions

For your protection, observe the following safety precautions

when setting up your equipment:

• Follow all cautions and instructions marked on the

equipment.

• Ensure that the voltage and frequency of your power

source match the voltage and frequency inscribed on the

equipment’s electrical rating label.

• Never push objects of any kind through openings in the

equipment. Dangerous voltages may be present.

Conductive foreign objects could produce a short circuit

that could cause fire, electric shock, or damage to your

equipment.

Symbols

The following symbols may appear in this book:

Caution – There is risk of personal injury and

equipment damage. Follow the instructions.

Caution – Hot surface. Avoid contact. Surfaces are

hot and may cause personal injury if touched.

Caution – Hazardous voltages are present. To reduce

the risk of electric shock and danger to personal

health, follow the instructions.

On – Applies AC power to the system.

Depending on the type of power switch your device has, one

of the following symbols may be used:

Off – Removes AC power from the system.

Standby – The On/Standby switch is in the standby

position.

Modifications to Equipment

Do not make mechanical or electrical modifications to the

equipment. Sun Microsystems is not responsible for

regulatory compliance of a modified Sun product.

Placement of a Sun Product

Caution – Do not block or cover the openings of your

Sun product. Never place a Sun product near a

radiator or heat register. Failure to follow these

guidelines can cause overheating and affect the