VM600Mk2/ VM600 ABE040 and ABE042 system racks

– Standard version 204-040-100-016

ABE040 Different versions of the VM600Mk2/VM600 ABE040 system rack:

– Standard version 204-040-100-015

– Varnished version, with a conformal coating for additional

environmental protection 204-040-100-015L

– Separate circuits version, in accordance with the IEC 60255-5 standard 204-040-100-115

– CCSAUS version, in accordance with the IEC 61010-1 standard 204-040-100-214

ABE042 Different versions of the VM600Mk2/VM600 ABE042 system rack:

– Version with mounting brackets positioned at the rear of the rack 204-042-100-01h

– Varnished version, with a conformal coating for additional

environmental protection 204-042-100-01hL

Different blank panel kits for the front of a VM600Mk2 ABE04x system rack:

– 1 × slot wide / 4 HP (TE) 200-505-011-012

– 3 × slots wide / 12 HP (TE) 200-505-018-012

Different blank panel kits for the rear of a VM600Mk2 ABE04x system rack:

– 1 × slot wide / 4 HP (TE) 200-505-011-012

Different blank panel kits for the front of a VM600 ABE04x system rack:

– 1 × slot wide / 4 HP (TE) 200-505-015-011

– 2 × slots wide / 8 HP (TE) 200-505-016-011

– 3 × slots wide / 12 HP (TE) 200-505-018-011

– 4 × slots wide / 16 HP (TE) 200-505-017-011

Different blank panel kits for the rear of a VM600 ABE04x system rack:

– 1 × slot wide / 4 HP (TE) 200-505-011-011

– 2 × slots wide / 8 HP (TE) 200-505-012-011

– 4 × slots wide / 16 HP (TE) 200-505-013-011

Notes

In an ordering number (PNR), “h” represents the hardware version.

The standard version of the VM600Mk2 ABE040 system rack (PNR 204-040-100-016) and the standard version of the VM600Mk2/VM600

ABE040 system rack (PNR 204-040-100-015 or earlier) are the same, except for the specific artwork/branding/finish. More specifically,

the mounting brackets on the side of the ABE040 system rack are bare aluminium for the VM600Mk2 versions and painted for the

VM600Mk2/VM600 versions. See also Ordering guidelines on page 9.

For safety reasons, any VM600Mk2/VM600 ABE04x system rack slot not populated by a module (card) must be covered by a blank

panel(s).

(The width of a 19″ rack is typically measured in horizontal pitch (HP) units of 5.08 mm (0.2″), also known as standard width (TE) units.

For the VM600Mk2/VM600 ABE04x System racks, a 1 × slot wide blank panel suitable for covering one module (card) position

corresponds to 4 HP (TE), a 2 × slots wide blank panel corresponds to 8 HP (TE), a 3 × slots wide blank panel corresponds to 12 HP (TE)

and so on.)

When only one RPS6U power supply is installed in a VM600Mk2/VM600 ABE04x system rack (PS1 in rack slots 18 to 20), the unused

power supply position (PS2 in rack slots 15 to 17) should be populated with a blank panel(s).

ORDERING GUIDELINES

The ordering numbers (PNRs) given in Ordering information on page 8 of this data sheet should be used when

ordering a VM600Mk2/VM600 ABE04x system rack and/or blank panels as individual system components for use

as a replacement or spare part.

However, when ordering these components with other system components as part of a complete

VM600Mk2/VM600 machinery monitoring system, then a VM600SYS-based ordering number should be used.

Contact your local Meggitt representative for further information.

RELATED PRODUCTS

VM600Mk2 (second generation)

ABE056 VM600Mk2/VM600 slimline rack : Refer to corresponding data sheet

ASPS VM600Mk2/VM600 auxiliary sensor power

supply