schneiderEnterasys® 800-Series Fast Ethernet/Gigabit Ethernet Switches

Hardware Installation Guide

08H20G4-24, 08H20G4-24P

08H20G4-48, 08H20G4-48P

08G20G2-08, 08G20G2-08P

08G20G4-24, 08G20G4-24P

08G20G4-48, 08G20G4-48P

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal 

vorgenommen werden.

Regulatory Compliance Information

Federal Communications Commission (FCC) Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not 

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause 

undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of 

the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is 

operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not 

installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this 

equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference 

at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment.

Industry Canada Notice

This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio

Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils 

numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des 

Communications du Canada.

Class A ITE Notice

WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the 

user may be required to take adequate measures. 

Clase A. Aviso de ITE

ADVERTENCIA: Este es un producto de Clase A. En un ambiente doméstico este producto puede causar interferencia de radio 

en cuyo caso puede ser requerido tomar medidas adecuadas.

Klasse A ITE Anmerkung 

WARNHINWEIS: Dieses Produkt zählt zur Klasse A ( Industriebereich ). In Wohnbereichen kann es hierdurch zu 

Funkstörungen kommen, daher sollten angemessene Vorkehrungen zum Schutz getroffen werden. 

VCCI Notice

This is a class A product based on the standard of the Voluntary Control Council for Interference by Information Technology 

Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble 

occurs, the user may be required to take corrective actions.

Hazardous Substances

This product complies with the requirements of European Directive, 2002/95/EC, Restriction of Hazardous Substances (RoHS) 

in Electrical and Electronic Equipment.

European Waste Electrical and Electronic Equipment (WEEE) Notice

Safety Information

Class 1 Laser Transceivers

The single mode interface modules use Class 1 laser transceivers. 

Read the following safety information before installing or operating these modules.

The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This control loop eliminates the 

need for maintenance checks or adjustments. The output is factory set, and does not allow any user adjustment. Class 1 Laser 

transceivers comply with the following safety standards:

• 21 CFR 1040.10 and 1040.11 U.S. Department of Health and Human Services (FDA).

• IEC Publication 825 (International Electrotechnical Commission).

• CENELEC EN 60825 (European Committee for Electrotechnical Standardization).

When operating within their performance limitations, laser transceiver output meets the Class 1 accessible emission limit of all 

three standards. Class 1 levels of laser radiation are not considered hazardous.

When the connector is in place, all laser radiation remains within the fiber. The maximum amount of radiant power exiting the 

fiber (under normal conditions) is -12.6 dBm or 55 x 10-6 watts.

Removing the optical connector from the transceiver allows laser radiation to emit directly from the optical port. The maximum 

radiance from the optical port (under worst case conditions) is 0.8 W cm-2 or 8 x 103 W m2

 sr-1. 

Do not use optical instruments to view the laser output. The use of optical instruments to view laser output increases eye 

hazard. When viewing the output optical port, power must be removed from the network adapter.

Safety Compliance

Warning: Fiber Optic Port Safety

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit