Honeywell C200 TK-PRS021

Disclaimer

This document contains Honeywell proprietary information. Information contained herein is to be

used solely for the purpose submitted, and no part of this document or its contents shall be

reproduced, published, or disclosed to a third party without the express permission of Honeywell

International Sàrl.

While this information is presented in good faith and believed to be accurate, Honeywell disclaims

the implied warranties of merchantability and fitness for a purpose and makes no express

warranties except as may be stated in its written agreement with and for its customer.

In no event is Honeywell liable to anyone for any direct, special, or consequential damages. The

information and specifications in this document are subject to change without notice.

Copyright 2019 - Honeywell International Sàrl

ABOUT THIS DOCUMENT

This guide provides information that will assist you in planning and designing activities, as well as

the installation, operation, and troubleshooting of C300 Process Controllers in a PlantCruise

system.

Starting with R501, C300 controllers (Hardware model — CC-PCNT02) provide an expanded

functionality of large memory capacity, primarily to support the Profit Controller. CC-PCNT02, with

the in-built firmware, is interoperable with CC-PCNT01 and enables easy synchronization,

Revision History

Revision Date Description

A August 2019 Initial release of the document.

C300 CONTROLLER PURPOSE

This section provides a quick comparison of C200 and C300 Controller features and reference to

topics in this book for a given task related to using the C300 Controller with the Experion system.

ATTENTION

The C300 Controller can be used with the Universal Input/Output (UIO) module for

replacing the TPS components such as Basic Controller (CB) and Extended Controller (EC).

For more information about the usage of the C300 Controller with the Universal

Input/Output (UIO) module, see Series 8 I/O User's Guide.

C300 Controller and C200 Controller comparison

The C300 Controller provides design improvements and greater operational capabilities for

process control over the chassis-based C200 controller. The following table is a listing that

compares design features and operational improvements of the C300 Controller with the C200

controller.

ATTENTION

The C300 - 20mS CEE Controller has all the features as the C300 - 50ms Controller with

exceptions related to the faster execution speed (20ms). The C300 - 20mS CEE controller

supports only the Series 8 I/O modules. Two new Series C I/O Modules (Speed Protection

Module (SPM) and Servo Valve Positioner Module (SVPM)) are only supported by the C300

- 20mS CEE Controller.

The C300 - 20mS CEE controller is only intended for Honeywell Turbine Control Solutions.

Controller

Feature

Comparison

Form Factor C200 - Chassis-based controller with plug-in modules for

Control Processor, I/O Link Interface, Redundancy, FTE

interface, Fieldbus, other I/O and control modules.

C300 - A single control module that plugs into an Input

Output Terminal Assembly (IOTA). Control module functions

include a Control processor, two I/O Link interfaces,

Controller

Feature

Comparison

Redundancy functions, and FTE interfaces.

Memory (RAM) C200 - 4MB User Memory

C300 - 16MB User Memory

Redundancy C200 -Two identically-equipped controller chassis that

contain two Redundancy Modules (RM) provide controller

redundancy.

C300 - Controller redundancy function is built in. A second

C300 Controller and redundancy cable is all that is required

for redundant controller operation. (No RMs)

I/O Link

Interface

C200 - An I/O Link Interface plug-in Module (IOLINK)

installed in the controller chassis is required to connect

PMIO I/O to the controller CPM.

C300 - Two I/O Link interfaces are built in to the controller.

Each I/O Link can connect with either PMIO I/O or Series 8

I/O modules.

Note: C300 - 20mS CEE Controller supports only Series 8

I/O modules.

Communications

Interface to

supervisory

network

C200 - Ethernet or Fault Tolerant Ethernet plug-in modules

are needed to connect to respective Ethernet and FTE

communication networks. ControlNet Interface plug-in

module is needed to connect with other ControlNet nodes.

C300 - Ethernet interface is built into the controller and

supports both Ethernet and redundant FTE

communications. No ControlNet interface.

Peer-to-Peer

Connections

C200 - Ethernet or Fault Tolerant Ethernet Bridge plug-in

modules are needed to connect to respective Ethernet and

FTE networks. ControlNet Interface plug-in module is

needed to connect with other ControlNet nodes.

C300 - Ethernet interface is built into the controller to

support both Ethernet and redundant FTE communications.

C300 connection to C200 controller is made through an

FTE Bridge module installed in the C200 chassis. No

ControlNet interface.

Note: C300 - 20mS CEE Controller does not support peerto-peer connection with C200E.

Function Blocks C200 and C300 - Both Controllers use the same standard

Experion function block types for control strategy execution.

There are some exceptions

Getting started

The following table lists some of the tasks covered in this document that are related to

implementing a C300 Controller in your Experion R300 system or later. If you are viewing this