MEGGITTVM600Mk2/ VM600 ABE040 and ABE042 system racks

– 1 × slot wide / 4 HP (TE) 200-505-015-011

– 2 × slots wide / 8 HP (TE) 200-505-016-011

– 3 × slots wide / 12 HP (TE) 200-505-018-011

– 4 × slots wide / 16 HP (TE) 200-505-017-011

Different blank panel kits for the rear of a VM600 ABE04x system rack:

– 1 × slot wide / 4 HP (TE) 200-505-011-011

– 2 × slots wide / 8 HP (TE) 200-505-012-011

– 4 × slots wide / 16 HP (TE) 200-505-013-011

Notes

In an ordering number (PNR), “h” represents the hardware version.

The standard version of the VM600Mk2 ABE040 system rack (PNR 204-040-100-016) and the standard version of the VM600Mk2/VM600 

ABE040 system rack (PNR 204-040-100-015 or earlier) are the same, except for the specific artwork/branding/finish. More specifically, 

the mounting brackets on the side of the ABE040 system rack are bare aluminium for the VM600Mk2 versions and painted for the 

VM600Mk2/VM600 versions. See also Ordering guidelines on page 9.

For safety reasons, any VM600Mk2/VM600 ABE04x system rack slot not populated by a module (card) must be covered by a blank 

panel(s).

(The width of a 19″ rack is typically measured in horizontal pitch (HP) units of 5.08 mm (0.2″), also known as standard width (TE) units.

For the VM600Mk2/VM600 ABE04x System racks, a 1 × slot wide blank panel suitable for covering one module (card) position 

corresponds to 4 HP (TE), a 2 × slots wide blank panel corresponds to 8 HP (TE), a 3 × slots wide blank panel corresponds to 12 HP (TE) 

and so on.)

When only one RPS6U power supply is installed in a VM600Mk2/VM600 ABE04x system rack (PS1 in rack slots 18 to 20), the unused 

power supply position (PS2 in rack slots 15 to 17) should be populated with a blank panel(s).

ORDERING GUIDELINES

The ordering numbers (PNRs) given in Ordering information on page 8 of this data sheet should be used when 

ordering a VM600Mk2/VM600 ABE04x system rack and/or blank panels as individual system components for use 

as a replacement or spare part.

However, when ordering these components with other system components as part of a complete

VM600Mk2/VM600 machinery monitoring system, then a VM600SYS-based ordering number should be used. 

Contact your local Meggitt representative for further information.

RELATED PRODUCTS

VM600Mk2 (second generation)

ABE056 VM600Mk2/VM600 slimline rack : Refer to corresponding data sheet

ASPS VM600Mk2/VM600 auxiliary sensor power 

supply

: Refer to corresponding data sheet

CPUMMk2 + IOCNMk2 VM600Mk2 rack controller and 

communications interface module

: Refer to corresponding data sheet

MPC4Mk2 + IOC4Mk2 VM600Mk2 machinery protection and 

condition monitoring module

: Refer to corresponding data sheet

RLC16Mk2 VM600Mk2 relay module : Refer to corresponding data sheet

RPS6U VM600Mk2/VM600 rack power supplies : Refer to corresponding data sheet

XMx16 + XIO16T VM600Mk2/VM600 condition monitoring 

modules

: Refer to corresponding data sheet

VibroSight VibroSight® machinery monitoring system 

software

: Refer to corresponding data sheet

VM600 (first generation)

ABE056 VM600Mk2/VM600 slimline rack : Refer to corresponding data sheet

AMC8 and IOC8T VM600 analog monitoring card pair : Refer to corresponding data sheet

ASPS VM600Mk2/VM600 auxiliary sensor power 

supply

: Refer to corresponding data sheet

CPUM and IOCN VM600 modular CPU card and

input/output card.

Note: With a front-panel display and support 

for Modbus RTU/TCP or PROFINET.

: Refer to corresponding data sheet

CPUR and IOCR VM600 rack controller and communications 

interface card pair.

Note: With rack controller redundancy and 

support for Modbus RTU/TCP.

: Refer to corresponding data sheet

CPUR2 and IOCR2 VM600 rack controller and communications 

interface card pair.

Note: With mathematical processing of 

fieldbus data and support for Modbus TCP 

and PROFIBUS.

: Refer to corresponding data sheet

IRC4 VM600 intelligent relay card : Refer to corresponding data sheet

MPC4 and IOC4T VM600 machinery protection card pair : Refer to corresponding data sheets

RLC16 VM600 relay card : Refer to corresponding data sheet

RPS6U VM600Mk2/VM600 rack power supplies : Refer to corresponding data sheet

XMx16 + XIO16T VM600Mk2/VM600 condition monitoring 

modules

: Refer to corresponding data sheet

Meggitt (Meggitt PLC) is a leading international engineering company, headquartered in England, that designs and delivers high-performance 

components and subsystems for aerospace, defence and selected energy markets. Meggitt comprises four customer-aligned divisions: 

Airframe Systems, Engine Systems, Energy & Equipment and Services & Support.

The Energy & Equipment division includes the Energy Sensing and Controls product group that specialises in sensing and monitoring solutions for a 

broad range of energy infrastructure, and control valves for industrial gas turbines, primarily for the Power Generation, Oil & Gas and Services markets. 

Energy & Equipment is headquartered in Switzerland (Meggitt SA) and incorporates the vibro-meter® product line, which has over 65 years of sensor 

and systems expertise and is trusted by original equipment manufacturers (OEMs) globally.