ABBACS1000 air-cooled

Term/Abbreviation Definition

PCC Point of common coupling The PCC is the point in the electrical power supply system where the responsibility of the utility changes to the industrial customer. The utility is responsible to provide clean voltage and current with respect to harmonic distortion up to the PCC. The industrial customer is responsible not to distort voltage and current by its electrical systems. PID controller Proportional-integral-derivative controller Control loop feedback system for controlling process variables (eg, pressure, flow) PE Protective earth PPCS Power plate communication system PPCS is an acronym for a serial communication protocol designed for data transfer via optical fibers between AMC circuit board and INTerface circuit boards. RTD Resistance temperature detector or device The RTD is a temperature sensor where the change in electrical resistance is used to measure the temperature. Supervisory signal Indicates the operating condition of a circuit or device. SW Software TC Short form for terminal compartment of the drive UPS Uninterruptible power supply Zero speed threshold Used in the manual to indicate that the drive has reached the value “zero speed” that is set in a parameter. The value can be set in the range of 0 and maximum speed (the unit for the speed is rpm).

Trademarks Names that are believed to be trademarks of other companies and organizations are designated as such. The absence or presence of such a designation should however not be regarded as an offense of the legal status of any trademark. The following registrations and trademarks are used in this manual:Trademark Definition Windows® Registered trademark of Microsoft Corporation Industrial IT™ Trademark of ABB DriveWare® Registered trademark of ABB Ethernet® Registered trademark of Xerox Corporation Profibus® Registered trademark of Profibus International (P.I.) Modbus® Registered trademark of the Modbus IDA organization Molykote® Registered trademark of Molykote

1.8 User’s responsibilities It is the responsibility of those in charge of the drive to ensure that each person involved in the installation, operation or maintenance of the drive has received the appropriate training and has thoroughly read and clearly understood the instructions in this manual and the relevant safety instructions. 

1.9 Intended use of equipment Those in charge of the drive must ensure that the drive is only used as specified in the contractual documents, operated under the conditions stipulated in the technical specifications and on the rating plate of the drive, and serviced in the intervals specified by ABB. Use of the drive outside the scope of the specifications is not permitted. Intended equipment use also implies that only spare parts recommended and approved by ABB must be used. Unauthorized modifications and constructional changes of the drive are not permitted. 

1.10 Cyber security disclaimer This product is designed to be connected to and to communicate information and data via a network interface. It is the customer's sole responsibility to provide and continuously ensure a secure connection between the product and Customer network or any other network (as the case may be). Customer shall establish and maintain any appropriate measures (such as but not limited to the installation of firewalls, application of authentication measures, encryption of data, installation of anti-virus programs, etc) to protect the product, the network, its system and the interface against any kind of security breaches, unauthorized access, interference, intrusion, leakage and/or theft of data or information. ABB and its affiliates are not liable for damages and/or losses related to such security breaches, any unauthorized access, interference, intrusion, leakage and/or theft of data or information

1.11 Quality certificates and applicable standards The following certificates and conformity declarations are available with ABB: - ISO 9001 and ISO 14001 certificates stating that ABB Switzerland Ltd has implemented and maintains a management system which fulfills the requirements of the normative standards - EC declaration of conformity - List of standards the drive complies wit

16] ANSI Z535.6 American national standard for product safety information in product manuals, instructions, and other collateral materials [17] ISO 3864-2:2004 (E) - Graphical symbols – Safety colors and safety signs – Part 2: Design principles for product safety labels [18] ISO 7010:2011 (E) - Graphical symbols - Safety colours and safety signs - Registered safety sign [19] EN 50110 European standard code for electrical work safety [20] ISO 13849-1 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design, section 6.2.6 Category 3 [21] IEC 60204-1 Safety of machinery - Electrical equipment of machines - Part 1: General requirements [22] IEC 60721-3-1 Classification of environmental conditions: Classification of groups of environmental parameters and their severities; Storage [23] IEC 60721-3-2 Classification of environmental conditions - Part 3-2: Classification of groups of environmental parameters and their severities - Transportation and Handling [24] IEC 60721-3-3 Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 3: Stationary use at weatherprotected location [25] IEC 62477-2 Safety requirements for power electronic converter systems and equipment – Part 2: Power electronic converters from 1 000 V AC or 1 500 V DC up to 36 kV AC or 54 kV DC