LAUERfor the operating consoles PCS 009, PCS 090, PCS 095, PCS 095.1

for the operating consoles

PCS 009, PCS 090, PCS 095, PCS 095.1

The operating consoles PCStopline offer the

highest degree on perfection, unparalled in

design and function. PCStopline keeps everything under control - from the PCSmini to the

PCSmaxi, with a superior operating culture and

an unlimited setup freedom.

PCS, the first programmable operating console

with a large selection of "ready-to-use" operating functions or operating tools which are

simply selected via instructions. You can realize

even the most unuasal operating requests at

ease and in a minimum of time.

Today this way and tomorrow that way

One standard hardware for virtually thousands

of different operating situations. Without extensive wiring and dozens of I/O points.

PCS for operating. What else?

■ Machine operation using 8 (PCS 009, PCS 090) or 16 (PCS 095, PCS 095.1)

freely assignable keys. These F01 to F08/F16 labeled keys can be application

specifically inscribed and are provided to the controller as status bits.

■ Machine operation using 4 (PCS 009), 16 (PCS 090) or 32 (PCS 095, PCS

095.1) freely usable LEDs. These can be assigned the indicating states ON,

DARK, FLASHING, and INVERSE FLASHING. A green and a yellow LED is allocated

to each function key.

■ Display of fixed texts with integrated variable values. The values can be

represented selectably as numerical values or in text format.

■ Representation of the contents of 233 words as variables. In addition, 650

external variables can be defined. 9 variable formats (from bit to timer) are

available.

■ 3 text groups, 128 operating texts as menu and idle texts, 128 message texts

with up to 332 lines, 5 help texts with up to 32 lines.

■ 127 menus with 255 menu nodes each for any menu configurations.

■ 4 different deletion modes. For every message, 1 of 4 possible deletion modes

can be selected.

■ Modification of the content of any word within the transfer area. Using the

integrated editor all possible representation formats can be setup.

■ 7 priority levels for idle text up to help text, 3 message priorities Information,

Warning, Fault. This working-condition related management significantly offloads the programmable controller program.

■ Monitoring of rising or falling edges of 128 consecutive bits. The assignment

of texts, the manage-ment of 3 priority levels (Information, Warnings, and Faults),

keeping the timely sequence as much as possible, organization of the FIRST

MESSAGE, LAST MESSAGE, and CYCLIC DISPLAY, the individually settable deletion behaviour, and the representation formats NORMAL and FLASHING are tasks

which are managed by the PCS by itself.

■ Communication monitoring (wire-break, short circuit). A very efficient data

transfer is secured by the integrated priority management in connection with the

intelligent package length optimization, the high thruput rate and the fault tole

Operator Panel PCS 009

1 = LCD-Display, 4 lines each with 40 characters

2 = Function keys (also as soft keys) F1...F8 with a

greem message LED

3 = 10 key keyboard for nominal value input

4 = cursor and control keys for menus and nominal

value input

5 = Switch key (Shift key) for function keys (F1..F4,

F5..F9)

6 = Important information LEDs on the PCS status

7 = Reset key

8 = DIL switch for the PCS 009

9 = Volume for acoustic signal

J = Serial interface RS 232/TTY for communication

K = Serial interface RS 422/RS 485 for communication

L = Operating voltage terminals

M = Fuse with reserve fuse

Operator Panel PCS 090

1 = LCD-display, 2 lines each with 40 characters

2 = Function keys (also as soft keys) F1...F8 with a

yellow and green message LED

3 = 10 key keyboard for nominal value input

4 = Cursor keys with LED and cursor control keys for

menus and nominal value input

5 = Important information LED's on the PCS status

6 = Reset key

7 = DIL-switch for the PCS 090

8 = Volume for acoustic signal

9 = Serial interface RS 232/TTY for the communication

J = Serial interface RS 422/RS 485 for the

communication

K = Operating voltage terminals

L = Fuse with reserve fuse

Operator Panel PCS 095/PCS 095.1

1 = LCD-display, 4 lines each with 40

characters

2 = Function keys (also soft keys) F1...F8

each with a yellow and a green

message LED

3 = Function keys F9...F16 each with a

yellow and a green mesage LED

4 = Ten key keyboard for nominal value

input

5 = Cursor key with LED and control key for

menu and nominal value input

6 = Important information LEDs on the PCS

status

7 = Reset key

8 = DIL switch for the PCS 095

9 = Volume for acoustic signals

J = Serial interface RS 232/TTY for the

communication

K = Serial interface RS 422/RS 485 for

the communication

L = Serial interface RS 232/TTY for the

programming and for the PCS 095.1

as Printer interface

M = Operating voltage terminals

N = Fuse with reserve fuse

Communication between any PLC and the PCS occurs as follows:

The PCS writes in predetermined word areas of the PLC, functions or nominal values,

which the PLC then reads and interprets.

The PLC writes in predetermined word areas functions or actual values, which are

automatically read and interpreted by the PCS. Independently of the PLC there are

maximum 256 words of 16 bit, that is to say 4096 inputs / outputs for the PCS/PLC