Woodward 2300E – Ordinary Locations 8273-1017

The 2300E is a digital control that can be programmed with applicable application software. This control is

housed in a sheet metal chassis and consists of a single printed circuit board. This control is designed to

perform the speed and load control functions for a small engine, steam turbine, or gas turbine. The 2300E

has no application software in it when shipped from Woodward, which allows it to be configured and

modified to meet site-specific requirements. It utilizes the Woodward GAP 3.X software to create an

application specific application software that can be downloaded to the 2300E.

The 2300E has the following Woodward part numbers:

8273-1017

2300E Load Sharing and Speed Control, 24 Vdc input, Ordinary

Locations

8273-1018

2300E Load Sharing and Speed Control, 24 Vdc input, Hazardous

Locations

The control is housed in a sheet-metal chassis and consists of a single printed circuit board. The 2300E is

set up and configured through an external computer connected at the 9-pin connector (RS-232 Port) at

the front of the control. The configuration software, Control Assistant, can be downloaded from our

website at www.woodward.com.

The 2300E has two serial communication ports, allowing it to easily interface with a Human Machine

Interface (HMI), PLC, or plant DCS. These configuration and dynamic settings are set, changed, tuned,

and saved via a laptop computer and Woodward’s user-friendly Control Assistant software program. This

program allows users to set and adjust all application-based parameters, plus upload and download

configurations to and from the control. Woodward’s Toolkit software is also capable of communicating to

the 2300E

The 2300E Control Hardware includes:

1 Load Sensor

• 1 Actuator Driver

2 MPU Speed Sensors

1 Analog Output

2 Analog Inputs

8 Discrete (Switch) Inputs

4 Discrete (Relay Driver) Outputs

2 Serial Ports

• 1 CAN Port

The following is an example of the typical hardware needed for a 2300E system controlling a single prime

mover and generator:

A 2300E electronic control

An external 18 to 36 Vdc power source

Two speed-sensing devices, typically magnetic pickups (MPUs)

A proportional actuator to position the fuel-metering device

Current and potential transformers for measuring the load carried by the generator

The frequency from the magnetic pickup must be within the range of 100 to 25 000 Hz at rated speed.

The 2300E speed range needs to be configured using an external computer during installation.

References

The following publications contain additional product or installation information on Load Sharing and

Speed Controls, and related components. They can be ordered from any Woodward office.

Manual Title

25070 Electric Governor Installation Guide 25195 Governing Fundamentals

82510 Magnetic Pickups and Proximity Switches for Electric Governors 82715 Guide for Handling

and Protection of Electronic Controls, Printed

Circuit Boards, and Modules

Product

Spec Title

03405 2300E Digital Load Sharing and Speed Control Hardware 82516

82575 EGB-1P/2P Governor/Actuator

This chapter contains general installation instructions for the 2300E control. Power requirements,

environmental precautions, and location considerations are included to determine the best location for the

control. Additional information includes unpacking instructions, electrical connections, and an installation

check- out procedure.

Before handling the control, read all of this chapter and “Electrostatic Discharge Awareness” at the

beginning of this manual. Be careful when unpacking the electronic control. Check the control for signs of

damage such as bent or dented panels, scratches, and loose or broken parts. If any damage is found,

immediately notify the shipper. Do not take the control out of the ESD bag it ships in until ESD

precautions are in place. Keep yourself discharged while handing the unit outside the ESD bag, at least

until it is grounded.

Power Requirements

The 2300E control requires a voltage source of 18 to 36 Vdc, with a current capacity of at least 600 mA

for operating power. If a battery is used for operating power, an alternator or other battery charging device

is necessary to maintain a stable supply voltage. The battery charging device should be suppressed from

load dump events or the power bus must have central suppression. The 2300E does not have sufficient

capability to withstand all battery load dump events.