ADLINK IH61-AA400-A4A1E (IMB-M40H) Industrial Motherboard
ADLINK IH61-AA400-A4A1E (IMB-M40H) Industrial Motherboard
The ADLINK IH61-AA400-A4A1E (part of the IMB-M40H series) is an ATX industrial-grade motherboard designed for long-lifecycle, high-reliability industrial automation,
machine vision, and embedded control systems. Powered by the Intel® H61 Express Chipset and supporting LGA1155 socket 2nd/3rd generation Intel® Core™ i7/i5/i3. Pentium®, and Celeron® processors, this board combines modern processing capability with legacy I/O flexibility (including 6 COM ports and 4 PCI slots).

1. Technical Specifications
| Feature / Parameter | Specifications |
| Model / Part Number | IH61-AA400-A4A1E (Series: IMB-M40H) |
| Form Factor | ATX (305 mm × 218 mm) |
| CPU Socket | LGA1155 |
| Supported Processors | 2nd/3rd Gen Intel® Core™ i7/i5/i3, Pentium®, Celeron® |
| Chipset | Intel® H61 Express Chipset |
| System Memory | 2× 240-pin DIMM sockets, Dual-Channel DDR3 1333/1600 MHz, up to 16 GB |
| BIOS | AMI 32 Mb SPI BIOS |
| Graphics Output | Integrated Intel® HD Graphics; VGA (up to 2048×1536) & DVI-D (up to 1920×1200) |
| Ethernet | Dual Gigabit LAN (2× Realtek® RTL8111E PCIe GbE controllers) |
| Expansion Slots | 1× PCIe x16 (Gen 2) 2× PCIe x1 (PCIe x1 signal via x4 slots) 4× 32-bit PCI slots |
| Storage | 4× SATA 3 Gb/s ports |
| Serial Ports (COM) | 6× COM total (5× RS-232, 1× RS-232/422/485) |
| USB Ports | Up to 10× USB 2.0 (4× rear I/O, 6× onboard headers) |
| Digital I/O (DIO) | 16-bit DI / 16-bit DO (16 in + 16 out) |
| Audio | Realtek® ALC892 High Definition Audio (Line-in, Line-out, Mic-in) |
| Watchdog Timer | Software programmable 1–255 sec / 1–255 min reset timer |
2. Environmental Tolerance Conditions
Operating Temperature: 0°C to 60°C (32°F to 140°F)
Operating Relative Humidity: 10% to 90% (non-condensing @ 40°C)
Vibration Resistance: 0.5 Grms, 5–500 Hz (random operating) / 2 Grms (non-operating)
Shock Resistance: 10 G peak acceleration (11 ms duration, operating)
Compliance & Certifications: CE, FCC Class A
3. Operating Instructions
Electrostatic Discharge (ESD) Protection: Wear an antistatic wrist strap connected to earth ground before handling the board.
CPU & Cooler Installation: Open the LGA1155 socket lever, insert the CPU aligned with the orientation keys, latch the lever down, and apply thermal grease before securing an industrial CPU cooler.
Memory Installation: Insert unbuffered DDR3 1333/1600 MHz DIMM modules into slots starting with DIMM_A1. Press firmly until the retaining clips snap into place.
Power Supply Connection: Connect standard 24-pin ATX power and 4-pin 12V CPU power cables from an industrial PSU.
Jumper Configuration: Set COM port operating mode jumpers (RS-232 vs. RS-422/485) prior to system bootup.
4. Fault Diagnosis & Troubleshooting
| Symptom | Likely Cause | Suggested Action |
| No Power / LED Off | Power supply disconnected or standard ATX PSU switch off. | Verify 24-pin and 4-pin ATX power cables; verify power button front-panel header pin connections. |
| Beep Codes / Continuous Beep | Memory seating failure or incompatible DDR3 RAM module. | Reseat DDR3 DIMMs; verify RAM specs (non-ECC, 1.5V DDR3 1333/1600 MHz). |
| No Display Output | Incorrect primary display setting or improper cable connection. | Verify VGA or DVI-D cable seating. Clear CMOS via onboard jumper CLR_CMOS if BIOS settings were modified incorrectly. |
| OS Boot Failure / Blue Screen | SATA mode mismatch (AHCI vs. IDE) or drive cable loose. | Access AMI BIOS setup (Del or F2 on startup) and check SATA mode settings. Verify SATA power and data cables. |
| Watchdog System Reset | Unresponsive software task triggering timer reset. | Check Watchdog application timeout intervals or disable WDT in BIOS during software debugging. |
5. Related Models in the Same Series
ADLINK IMB-M40H Series:
IH61-AA400-A4A1E (Standard variant with dual LAN, 6 COM ports, 4 PCI slots)
IMB-M40 (Base model variant)
ADLINK IMB-M42H Series:
Next-generation revision built on the Intel® H81 chipset for 4th Gen Intel Core processors (LGA1150).
ADLINK IMB-M43 Series:
Updated industrial ATX series supporting Intel® Q170/H110 chipsets for 6th/7th Gen Intel processors.
6. Storage Conditions
Storage Temperature: -20°C to 80°C (-4°F to 176°F)
Storage Humidity: 5% to 95% RH (non-condensing)
Packaging: Keep inside original ESD protective anti-static bag with desiccant gel until installation.
Warehouse Requirements: Store in a dry, dust-free environment away from corrosive gases, strong magnetic fields, and direct sunlight.
| User name | Member Level | Quantity | Specification | Purchase Date |
|---|