ADLINK PCI-8124-C Advanced 4-CH Encoder Card

ADLINK PCI-8124-C Advanced 4-CH Encoder Card

PCI-8124-C

Advanced 4-CH Encoder Card with High-speed Triggering Function

Key Features

32-bit PCI bus, Rev. 2.2. 33 MHz

Card index switch selection

Encoder input interface: OUT/DIR, CW/CCW, and 1x, 2x, 4x A/B phase

Trigger output up to 5 MHz; encoder input up to 20 MHz

Programmable trigger pulse width: 0.1 us to 3.2765 ms

Input/Output circuit source can be selectable: TTL/Open

Internal high-speed FIFO for four 32-bit comparators as data

Each channel can store 1024 points (32-bit)

PCI-8124-C is a 4-CH trigger board which is suitable for advanced line scan application which need high line rates. PCI-8124-C has internal FIFO to realize the high speed position compare and trigger pulse output.

For this application, ADLINK proposes you can use PCI-8134 and PCI-8124-C together to gain the advantage of motion control and high speed trigger function.

For position compare, PCI-8124-C provides two method: linear function or variable interval.

PCI-8124-C also provides the variety of mapping function between comparator and trigger output. The comparator condition can be associated with latch signal, TTL input and EA/EB signal.

Ordering Information

PCI-8124-CAdvanced 4-CH encoder card with high-speed triggering function

Accessory

DIN-50S-01Terminal Board with one 50-pin SCSI-II connector and DIN-rail mounting

ACL-10250-150-pin SCSI-II cable (mating with AMP-787082-5), 1 M

Specifications

Counter

■Number of Channels

■Trigger Pulse Frequency

■Encoder Counter

■Comparator

■FIFO Capacity

■Encoder Input Frequency

■Trigger Pulse Width

I/O Signals

■Partial I/O Signals

■Partial I/O Signals

Features

■ 32-bit PCI bus, Rev. 2.2. 33 MHz

■ Card index switch selection

■ Four 32-bit quadrature encoder input and trigger output

channels

■Encoder Signals Input Pins

■Encoder Index Signal Input Pin

■Position latch Input Pin

■Trigger Pulse Output Pin

General Specifications

■Connectors

4-CH

5 MHz (max.)

4. 32-bit

14. 32-bit

1.023 points/channel

20 MHz (max.) @ 4 x AB mode

0.1 us to 3.2765 ms

Optically isolated with 2500 VRMS isolation voltage

TTL type

EA and EB

EZ

LTC

TRG, 5 V pulse output reference to ground

50-pin SCSI-type connector

■Operating Temperature

■Storage Temperature

■ Encoder input interface: OUT/DIR, CW/CCW, and 1x, 2x,

4x A/B phase

■ Trigger output up to 5 MHz

■ Encoder input up to 20 MHz

■ Programmable trigger pulse width: 0.1 us to 3.2765 ms

■ Input/Output circuit source can be selectable: TTL/Open

collector (with isolation)

■ Switch setting for trigger output default level while power on

■ Trigger output pin logic programmable

■Digital filter for individual encoder input channel

■ Internal high-speed FIFO for four 32-bit comparators as data

reload buffer

■ Each channel can store 1.023 points (32-bit)

■ Each trigger output channel is selected from all comparators,

and manual trigger commands

■ Each encoder counter source is selected from comparators

and manual trigger commands

■ Trigger Pulse Counter

■ 14 comparators can select one of 4 trigger output channels

individually

■ 4 comparators for comparing encoder counter and FIFO data

■ 10 comparators for comparing encoder counter and linear data

■ 4 channel TTL output pins for general purpose output or

trigger output

■ 4 channel TTL input pins for general purpose or timer start signal

■ 4 channel high speed latch input pins for counters

■ EZ and Latch input pins can be used for general purpose input

■ Encoder counter clear via EZ input pin as zero operation by

rising or falling edge

■ Programmable interrupt sources from linear data finished,

triggered, FIFO empty/full/low, latched, and TTL input on

■Humidity

Power Consumption

■Slot Power Supply (input)

■External Power Supply (output)

Software Support

■    OS Information

•    Windows® 8/7/XP

•    RTX 5.x/6.x/8.1a

■    Software Compatibility

•    VB/VC++/BCB/Delphi

•    Various sample programs with source codes

■    Software Recommendations

•    TriggerMaster

Ordering Information

■ PCI-8124-C

Advanced 4-CH encoder card with high-speed

triggering function

Accessories

For more information on terminal boards & cables, please refer to page 3-30.

Terminal Board

■    DIN-50S-01

Terminal board with one 50-pin SCSI-II connector and

DIN-rail mounting

0˚C to +50˚C (32˚F to 122˚F)-20˚C to +80˚C (-4˚F to 176˚F)

5% to 85%, non-condensing

900 mA (Max.) ±5%, 900 mA (Max.)

+5 VDC ±5%, 500 mA (Max.)