EMERSONIPMC7126E/7616E I/O Module

SCSI Type Width Speed

FAST SCSI Narrow (8 bit) 10MB/second

FAST SCSI Wide (16 bit) 20MB/second

Ultra SCSI Narrow (8 bit) 20MB/second

Ultra SCSI Narrow (16 bit) 40MB/second

Trademarks

Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of 

Emerson Electric Co. © 2008 Emerson Electric Co. 

All other trademarks are the property of their respective owners. 

PICMG®, CompactPCI®, AdvancedTCA™ and the PICMG, CompactPCI and AdvancedTCA logos are registered trademarks of the PCI Industrial 

Computer Manufacturers Group.

Notice

While reasonable efforts have been made to assure the accuracy of this document, Emerson assumes no liability resulting from any omissions 

in this document, or from the use of the information obtained therein. Emerson reserves the right to revise this document and to make changes 

from time to time in the content hereof without obligation of Emerson to notify any person of such revision or changes.

Electronic versions of this material may be read online, downloaded for personal use, or referenced in another document as a URL to a Emerson 

website. The text itself may not be published commercially in print or electronic form, edited, translated, or otherwise altered without the 

permission of Emerson,

It is possible that this publication may contain reference to or information about Emerson products (machines and programs), programming, or 

services that are not available in your country. Such references or information must not be construed to mean that Emerson intends to announce 

such Emerson products, programming, or services in your country.

Limited and Restricted Rights Legend

If the documentation contained herein is supplied, directly or indirectly, to the U.S. Government, the following notice shall apply unless otherwise 

agreed to in writing by Emerson.

Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (b)(3) of the Rights in Technical Data 

clause at DFARS 252.227-7013 (Nov. 1995) and of the Rights in Noncommercial Computer Software and Documentation clause at DFARS

252.227-7014 (Jun. 1995).

Contact Address

Emerson Network Power - Embedded Computing 

2900 South Diablo Way, Suite 190 

Tempe, AZ 85282

USA

Safety Summary

The following general safety precautions must be observed during all phases of operation, service, and repair

of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual

could result in personal injury or damage to the equipment.

The safety precautions listed below represent warnings of certain dangers of which Emerson is aware. You,

as the user of the product, should follow these warnings and all other safety precautions necessary for the

safe operation of the equipment in your operating environment.

Ground the Instrument.

To minimize shock hazard, the equipment chassis and enclosure must be connected to an electrical ground.

If the equipment is supplied with a three-conductor AC power cable, the power cable must be plugged into

an approved three-contact electrical outlet, with the grounding wire (green/yellow) reliably connected to an

electrical ground (safety ground) at the power outlet. The power jack and mating plug of the power cable meet

International Electrotechnical Commission (IEC) safety standards and local electrical regulatory codes.

Do Not Operate in an Explosive Atmosphere.

Do not operate the equipment in any explosive atmosphere such as in the presence of flammable gases or

fumes. Operation of any electrical equipment in such an environment could result in an explosion and cause

injury or damage.

Keep Away From Live Circuits Inside the Equipment.

Operating personnel must not remove equipment covers. Only Factory Authorized Service Personnel or other

qualified service personnel may remove equipment covers for internal subassembly or component

replacement or any internal adjustment. Service personnel should not replace components with power cable

connected. Under certain conditions, dangerous voltages may exist even with the power cable removed. To

avoid injuries, such personnel should always disconnect power and discharge circuits before touching

components.

Use Caution When Exposing or Handling a CRT.

Breakage of a Cathode-Ray Tube (CRT) causes a high-velocity scattering of glass fragments (implosion). To

prevent CRT implosion, do not handle the CRT and avoid rough handling or jarring of the equipment.

Handling of a CRT should be done only by qualified service personnel using approved safety mask and

gloves.

Do Not Substitute Parts or Modify Equipment.

Do not install substitute parts or perform any unauthorized modification of the equipment. Contact your local

Emerson representative for service and repair to ensure that all safety features are maintained.

Observe Warnings in Manual.

Warnings, such as the example below, precede potentially dangerous procedures throughout this manual.

Instructions contained in the warnings must be followed. You should also employ all other safety precautions