EMERSONIPMC7126E/7616E I/O Module

which you deem necessary for the operation of the equipment in your operating environment.

Warning

Warning To prevent serious injury or death from dangerous voltages, use 

extreme caution when handling, testing, and adjusting this 

equipment and its components.

Flammability

All Emerson PWBs (printed wiring boards) are manufactured with a flammability rating of 94V-0 by UL-recognized 

manufacturers.

EMI Caution

!

Caution

Caution This equipment generates, uses and can radiate electromagnetic energy. It may cause or be 

susceptible to electromagnetic interference (EMI) if not installed and used with adequate EMI 

protection.

CE Notice (European Community)

!

Warning

Warning This is a Class A product. In a domestic environment, this product may cause radio 

interference, in which case the user may be required to take adequate measures.

Emerson products with the CE marking comply with the EMC Directive (89/336/EEC). Compliance with this directive 

implies conformity to the following European Norms:

EN55022 “Limits and Methods of Measurement of Radio Interference Characteristics of Information 

Technology Equipment”; this product tested to Equipment Class A

EN 300 386 V.1.2.1 “Electromagnetic compatibility and radio spectrum matters (ERM); 

Telecommunication network equipment; Electromagnetic compatibility (EMC) requirements”

Board products are tested in a representative system to show compliance with the above mentioned requirements. 

A proper installation in a CE-marked system will maintain the required EMC/safety performance.

In accordance with European Community directives, a “Declaration of Conformity” has been made and is on file 

within the European Union. The “Declaration of Conformity” is available on request. Please contact your sales 

representative.

The product has been designed to meet the directive on the restriction of the use of certain hazardous substances 

in electrical and electronic equipment (RoHS) Directive 2002/95/EC.

Industrie Canada

This product meets the requirements of the Canadian Interference-Causing Equipment Standard ICES-003.

Cet appareil numérique est conforme à la norme NMB-003 du Canada

The IPMC7126E/7616E I/O Module Installation and Use manual provides the information you 

will need to install, use, and program your IPMC7126E or IPMC7616E module. These are 

optional I/O modules installed on the variants of the MVME5100, MVME5500 and MVME6100 

Single Board Computers (SBCs). Their design utilizes the PowerPlus II architecture. Hereafter, 

the IPMC7126E and IPMC7616E modules will be referred to as the IPMC712 and IPMC761.

The IPMC712 is a variation of the IPMC761 The primary differences between the two modules 

are in the physical interfaces of the Ethernet port and serial ports 3 and 4. These differences 

along with others are discussed in the following chapters of this manual.

As of the printing date of this manual, these I/O module models are available:

This manual is organized as follows:

■ Chapter 1, Product Features

■ Chapter 2, Installing the IPMC Module

■ Chapter 3, Programming

■ Chapter 4, Connector Pin Assignments

■ Appendix A, Specifications

■ Appendix B, Related Documentation

Summary of Changes

See the table below for manual revisions and changes.

Model Number Product Description and I/O Features

IPMC7126E-002 Multifunction rear I/O PMC module; Ultra-Wide SCSI, one parallel port, 

three asynchronous and one synchronous/asynchronous serial port

IPMC7616E-002 Multifunction rear I/O PMC module; Ultra-Wide SCSI, one parallel port, 

two asynchronous and two synchronous/asynchronous serial ports

See the table below for manual revisions and changes.

Model Number Product Description and I/O Features

IPMC7126E-002 Multifunction rear I/O PMC module; Ultra-Wide SCSI, one parallel port, 

three asynchronous and one synchronous/asynchronous serial port

IPMC7616E-002 Multifunction rear I/O PMC module; Ultra-Wide SCSI, one parallel port, 

two asynchronous and two synchronous/asynchronous serial ports

Part Number Date Description 

6806800A45B September 2008 Update document to Emerson style (logo, copyright, 

trademarks, etc.)

Comments and Suggestions

We welcome and appreciate your comments on our documentation. We want to know what you 

think about our manuals and how we can make them better. 

Mail comments to us by filling out the following online form: 

http://www.emersonnetworkpowerembeddedcomputing.com/ > Contact Us > Online Form

In “Area of Interest” select “Technical Documentation”. Be sure to include the title, part number, 

and revision of the manual and tell us how you used it.

Terminology

A character precedes a data or address parameter to specify the numeric format, as follows (if 

not specified, the format is hexadecimal. An asterisk (#) following a signal name for signals that 

are level significant denotes that the signal is true or valid when the signal is low.

An asterisk (#) following a signal name for signals that are edge significant denotes that the # 

actions initiated by that signal occur on high to low transition.