KEBAKeConnect I/O modules KeConnect DI 240/B, DI 260/A Digital input modules

KeConnect DI 240/B, DI 260/A

Digital input modules

Product features

• Up to 16 digital inputs

• 2 digital inputs with interrupt

• Electronic parameter chip

• Configurable input filter

Short description

The digital input module of the DI 2xx/x series enables the connection of 8 (DI 240/B) or 16 (DI 260/A) digital inputs. 

24 V DC control signals are captured by the digital inputs and transmitted galvanically isolated to the higher-level automation device. In addition, two digital inputs can be used as interrupt inputs.

These modules are attached directly to a CPU module or can be operated with all KEBA controls by means of bus 

couplers.

Digital inputs

DI 240/B DI 260/A

Number of inputs 8 16

Input type Type 1 (acc. to EN 61131-2)

Voltage range for "1" 15 V ≤ UH ≤ 30 V

Voltage range for "0" -3 V ≤ UL ≤ 5 V

Status display Green LED

Galvanic isolation Yes, electric strength 707 V with isolated ground connection

Cycle time 1 ms

Debouncing Configurable 1 ms, 100 ms

Interrupt inputs

Number of inputs 2 (DI0, DI1) of the digital inputs

Input type Type 1 (acc. to EN 61131-2)

Voltage range for "1" 15 V ≤ UH ≤ 30 V

Voltage range for "0" -3 V ≤ UL ≤ 5 V

Response time of the K-bus interrupt 100 μs with 5 kHz input filter

Status display Green LED

Galvanic isolation Yes

Dimensions, weight

Height 120 mm

Width 22.5 mm front plate / 32.5 mm incl. K-bus plug

Depth 100 mm

Weight 130 g

General

I/O supply voltage 24 V DC from K-bus

5 V DC from K-bus

Overvoltage category II

Protection class III acc. to EN 61131-2

Addressing on K-bus Via 16-digit address switch, on the side

Type of terminals Open - pitch 5.08 mm

Max. power consumption K-bus 24 V 1 W

Max. power consumption K-bus 5 V 0.4 W

Product features

• 8 or 14 digital outputs

• Short-circuit detection and diagnosis

• Permanently short-circuit proof

• Current load capacity 2 A at 50 % simultaneity

• Fast shutdown function for inductive loads

• Electronic parameter chip

Short description

Digital output modules DO 242/B and DO 272/A enable the connection of up to 14 digital outputs. The digital outputs 

switch the 24 V DC control signals of a central module galvanically isolated from the connected actuators and are designed for a load of up to 2 A at 50 % simultaneity. 

The modules are equipped with a fast shutdown function that enables a rapid shutdown of inductive loads, e.g., hydraulic valves. Machine processes can thereby be accelerated and productivity increased. 

The operational safety is ensured by the permanent short-circuit protection of the outputs. Should a short circuit occur, 

it is detected and reported to the control module.

These modules are attached directly to a CPU module or can be operated with all KEBA controls by means of bus 

couplers

Digital outputs

DO 242/B DO 272/A

Number of outputs 8 14

Nominal voltage 24 V DC

Processing time 1 ms

Nominal current of digital outputs 2 A at 50 % simultaneity

Galvanic isolation Yes

Status display Orange LED

Protection facility Short-circuit protection

Max. inductive load 1 J at max 0.2 Hz

Dimensions, weight

Height 120 mm

Width 22.5 mm front plate / 32.5 mm incl. plug

Depth 100 mm

Weight 130 g

General

DO 242/B DO 272/A

Supply voltage 24 V DC from front (nominal voltage tolerance: 19.2 V … 30 V, acc. to EN 61131-2)

24 V DC from K-bus, 5 V DC from K-bus

Overvoltage category II

Protection class III acc. to EN 61131-2

Addressing on K-bus Via 16-digit address switch, on the side

Type of terminals Open - pitch 5.08 mm

Displays on the front plate 16 signal status LEDs

Max. power consumption K-bus 24 V 2.1 W 2.1 W

Max. power consumption K-bus 5 V 0.4 W 0.4 W

Environmental conditions

Operating temperature +5 °C … +55 °C

Storage temperature -40 °C … +70 °C

Relative air humidity 10 % to 95 % (non-condensing)

Vibration resistance / shock resistance Acc. to EN 61131-2

Product features

• Up to 8 digital inputs

• 8 digital 2 A outputs

• 2 digital inputs with interrupt

• Short-circuit detection

• Permanently short-circuit proof

• Electronic rating plate

Short description

The DM 27x/A series is a digital input/output module of the KeConnect C2 product line and enables the connection of 6 

or 8 digital inputs and 8 digital outputs. 24 V DC control signals are captured by the digital inputs and transmitted galvanically isolated to the higher-level automation device. In addition, two of the digital inputs can be used as interrupt inputs. 

The digital outputs switch the 24 V DC control signals of a CPU module galvanically isolated from the connected actuators. In addition to the short-circuit connection, outputs that cause short circuits can be switched off individually.

This module is attached directly to a CPU module or can be operated with all KEBA controls by means of a bus coupler.

Digital inputs

DM 272/A DM 276/A

Number / wiring of inputs 8x sink 6x source

Input type Type 1 (acc. to EN 61131-2)

Voltage range for "1" 15 V ≤ UH ≤ 30 V

Voltage range for "0" -3 V ≤ UL ≤ 5 V

Debouncing Configurable 1 ms, 100 ms

Cycle time 1 ms

Status display Green LED

Galvanic isolation Yes, electric strength 707 V with isolated ground connection

Interrupt inputs

Number of inputs Two of the digital inputs can be used as interrupt inputs