ABBEasyLine EL3000 Series

Pressure sensor

Use

Standard: with Uras26, Limas23, Caldos27,

Option: with Magnos206, Magnos28 and Magnos27

Working range

pabs = 600–1250 hPa

Materials in contact with the sample medium

Silicone gel, plastics, FPM (Fluorocarbon rubber)

Sample gas composition

The pressure sensor must not be connected to the sample gas

path when the sample gas is corrosive, flammable or explosive.

Fine filtration

Version

Disposable filter with borosilicate glass microfiber filter element

(supplied as accessory)

Retention rate

99.99 % for particles > 0.1 µm

Materials in contact with the sample medium

Polyamide, borosilicate glass with PVDF binder

Safety

Tested per EN 61010-1:2010

Protection class I

Overvoltage category/pollution degree

II/2

Safe isolation

The power supply is galvanically isolated from other circuits by

means of reinforced or double insulation. Protective extra-low

voltage (PELV) on low-voltage side

Electromagnetic compatibility

Noise immunity

Tested to EN 61326-1:2013. Inspection severity: Industrial area,

fulfills at least the test requirements to table 2 of EN 61326.

Emitted interference

Tested to EN 61326-1:2013. Limit value class B for interference

field strength and interference voltage is met.

Mechanical stress

Operation

Vibration test to EN 60068-2-6:1996

In Uras26, slight transient effects on the measured value can occur in the region of the modulation frequency.

Transport

Vibration test to EN 60068-2-6:1996,

shock test to EN 60068-2-27:1995

In its original packaging, the gas analyzer will withstand normal

shipping conditions.

Installation site requirements

Installation location

The gas analyzer is intended for indoor installation only. Installation location altitude max. 2000 m above sea level (over 2000 m

on request)

Ambient temperature

Operation: +5 to +45 °C, Uras26 in combination with another analyzer, Limas23, Fidas24: +5 to +40 °C, Storage and transport:

−25 to +65 °C

Relative humidity

< 75 %, slight condensation allowed

Air circulation

For sufficient air circulation, multiple housings in a 19-inch rack

must be installed with a separation of at least one height unit between housings.

Power supply

Input voltage

AC 100 to 240 V − 15/+ 10 %, 50 to 60 Hz ± 3 Hz

Power consumption

Max. 187 VA

Connection

3-pin plug per EN 60320-1/C14; connection cable supplied.

Connection diagrams see page 24.

Individual analyzers

Input voltage

DC 24 V ± 5 %

Power consumption

Uras26: max. 95 W Magnos27: max. 35 W

Limas23: max. 100 W ZO23: max. 35 W

Magnos206: max. 50 W Caldos27: max. 17 W

Magnos28: max. 50 W Fidas24: max. 40 W

Fidas24: Heating of detector and sample gas inlet

Input voltage

AC 115 V or 230 V, ± 15 % (max. 250 V), 47 to 63 Hz

Power consumption

125 VA for detector heating,

125 VA for heated sample gas inlet (option)

Connection

4-pin plug; connection cable supplied.

Connection diagrams see page 35.

Note regarding the analyzers performance characteristics

The performance characteristics of the analyzers have been determined according to IEC 61207-1:2010 “Expression of performance of gas analyzers – Part 1: General”. They are based on operation at atmospheric pressure (1013 hPa) and nitrogen as the

associated gas. Compliance with these characteristics when

measuring other gas mixtures can only be assured if their composition is known. The physical detection limit is the lower limit

of the performance characteristics relative to the measuring

range span.