ProSoftMVI56E-MNETCR ControlLogix Platform Modbus TCP/IP Multi Client Enhanced Communications Module for Remote Chassis

ProSoft Configuration Builder (PCB) (included) 

ProSoft Discovery Service (PDS) (included in PCB) 

Pentium®

 II 450 MHz minimum. Pentium III 733 MHz (or better) 

recommended 

Supported operating systems: 

o Microsoft Windows®

 Vista 

o Microsoft Windows XP Professional with Service Pack 1 or 2 

o Microsoft Windows 2000 Professional with Service Pack 1, 2, or 3 

o Microsoft Windows Server 2003 

128 Mbytes of RAM minimum, 256 Mbytes of RAM recommended 

100 Mbytes of free hard disk space (or more based on application 

requirements) 

256-color VGA graphics adapter, 800 x 600 minimum resolution (True Color 

1024 × 768 recommended) 

CD-ROM drive 

Note: The Hardware and Operating System requirements in this list are the minimum 

recommended to install and run software provided by ProSoft Technology®. Other third party 

applications may have different minimum requirements. Refer to the documentation for any third 

party applications for system requirements. 

Note: You can install the module in a local or remote rack. For remote rack installation, the module 

requires EtherNet/IP or ControlNet communication with the processor. 

Setting Jumpers 

The Setup Jumper acts as "write protection" for the module’s flash memory. In 

"write protected" mode, the Setup pins are not connected, and the module’s 

firmware cannot be overwritten. Do not jumper the Setup pins together unless 

you are directed to do so by ProSoft Technical Support. 

The following illustration shows the MVI56E-MNETCR jumper configuration

Note: If you are installing the module in a remote rack, you may prefer to leave the Setup pins 

jumpered. That way, you can update the module’s firmware without requiring physical access to 

the module. 

Installing the Module in the Rack 

If you have not already installed and configured your ControlLogix processor and 

power supply, please do so before installing the MVI56E-MNETCR module. 

Refer to your Rockwell Automation product documentation for installation 

instructions. 

Warning: You must follow all safety instructions when installing this or any other electronic 

devices. Failure to follow safety procedures could result in damage to hardware or data, or even 

serious injury or death to personnel. Refer to the documentation for each device you plan to 

connect to verify that suitable safety procedures are in place before installing or servicing the 

device. 

After you have checked the placement of the jumpers, insert the MVI56EMNETCR into the ControlLogix chassis. Use the same technique recommended 

by Rockwell Automation to remove and install ControlLogix modules. 

You can install or remove ControlLogix system components while chassis power 

is applied and the system is operating. However, please note the following 

warning. 

Warning: When you insert or remove the module while backplane power is on, an electrical arc 

can occur. An electrical arc can cause personal injury or property damage by sending an 

erroneous signal to your system’s actuators. This can cause unintended machine motion or loss of 

process control. Electrical arcs may also cause an explosion when they happen in a hazardous 

environment. Verify that power is removed or the area is non-hazardous before proceeding. 

Repeated electrical arcing causes excessive wear to contacts on both the module and its mating 

connector. Worn contacts may create electrical resistance that can affect module operation. 

1 Align the module with the top and bottom guides, and then slide it into the 

rack until the module is firmly against the backplane connector. 

2 With a firm, steady push, snap the module into place. 

3 Check that the holding clips on the top and bottom of the module are securely 

in the locking holes of the rack

4 Make a note of the slot location. You must identify the slot in which the 

module is installed in order for the sample program to work correctly. Slot 

numbers are identified on the green circuit board (backplane) of the 

ControlLogix rack. 

5 Turn power ON. 

Note: If you insert the module improperly, the system may stop working or may behave 

unpredictably. 

1.6 Installing the Configuration Tools 

1.6.1 Installing ProSoft Configuration Builder 

To install ProSoft Configuration Builder from the CD-ROM

1 Insert the ProSoft Solutions CD-ROM into the CD drive of your PC. Wait for 

the startup screen to appear. 

2 On the startup screen, click INSTALL PROSOFT CONFIGURATION BUILDER. This 

action starts the installation wizard for ProSoft Configuration Builder. 

3 Click NEXT on each page of the installation wizard. Click FINISH on the last 

page of the wizard. 

1.7 Connecting Your PC to the Module 

With the module securely mounted, connect one end of the Ethernet cable to the 

Config (E1) Port, and the other end to an Ethernet hub or switch accessible from