MOVIDRIVE® MDX60B / 61B Operating Instructions

shield clamps comprises:

– 2 shield clamps for power cable (2 contact clips each)

– 1 shield clamp for signal cable (1 contact clip) for MDX60B

– 1 shield clamp for signal cable (2 contact clips) for MDX61B

– 6 contact clips

– 6 screws for attaching the contact clips

– 3 screws for attaching the contact clips to the unit

Sizes 1-6 • 1 set of shield clamps for signal cable, not installed. The set of shield clamps comprises:

– 1 shield clamp for signal cable (1 contact clip)

– 2 contact clips

– 2 screws for attaching the contact clips

– 1 screw for attaching the shield clamp to the unit

• Only for size 6: Carrying bar and 2 split pins

Size 2S • Accessories set, not installed. The accessories set (→ Following illustration) comprises:

– 2 mounting feet [1] to be plugged into the heat sink

– 2 touch guards [2] to be fastened to terminals X4: -Uz/+Uz and X3:-R(8)/+R(9).

Once the touch guards [2] have been installed, the enclosure is IP20. Otherwise

it is IP10 (→ Section "Touch guards").

Optional scope of delivery

All sizes • Option DBM60B: Door installation for separate mounting of the DBG60B keypad

(e.g. in the control cabinet).

Part number 824,853 2.

The DBM60B option consists of the housing with enclosure IP65 and a 5 m extension cable (→ Following illustration). Das Bediengerät DBG60B ist in dieser Option

nicht enthalten und muss separat bestellt werden.

• Option DKG60B: 5 m Verlängerungskabel für Bediengerät DBG60B.

Part number 817 583 7.

5 m extension cables are available for mounting the keypad separately in customer

housing (→ Following illustration). 

Size 2 S • DMP11B mounting panel (→ following figure), not installed.

Part number 818 398 8.

If a MOVIDRIVE® MD_60A size 2 unit is to be replaced by MOVIDRIVE® MDX61B

size 2S, the MDX61B size 2S can be fitted on the existing mounting plate with the

DMP11B mounting panel. New retaining holes do not have to be drilled.

54588AXX

DMP11B

Connector adapter 

for replacing 

MOVIDRIVE® A 

with 

MOVIDRIVE® B

The following adapters are available for rapid replacement of a MOVIDRIVE® A unit with

a MOVIDRIVE® B unit.

• DAT11B: Terminal adapter, part number 824 671 8

X10 can be rearranged directly when using MOVIDRIVE® MDF, MDV or MDS. Three

plugs have to be rewired. You can avoid such rewiring work by using the DAT11B

terminal adapter. Using this adapter will prevent incorrect connection and save time.

The terminal adapter is required for terminals X11 (analog input), X12 (SBus) and

X13 (binary inputs).

• DAE14B: Encoder adapter X14, part number 817 630 2

If a synchronous encoder is operated at X14 on MOVIDRIVE® MDV, MDS, MCV or

MCS, connection takes place via a 9-pin connector. Since the DEH11B and DER11B

options for MOVIDRIVE® MDX61B come equipped with a 15-pin plug, you will either

have to rework the encoder cable or use the encoder adapter. The encoder adapter

can be plugged directly between the existing encoder cable with 9-pin socket and the

15-pin connector on DEH11B/DER11B. This step makes for fail-safe and fast connection of existing drives

• DWE11B: Interface adapter (adapter cable), part number 188 187 6

The interface adapter DWE11B (HTL→TTL) in the form of an adapter cable is used

to connect single-ended HTL encoders to the HIPERFACE®encoder card

DEH11B. Only the A, B and C tracks are connected. The interface adapter is suitable

for all HTL encoders that were operated on MOVIDRIVE® A, MDV and MCV and can

be connected without any rewiring effort

[1] X1: Power supply connection 1/L1, 2/L2, 3/L3, separable

[2] X4: Connection for DC link connection –UZ +UZ, separable

[3] Fieldbus slot

[4] Expansion slot

[5] Encoder slot

[6] X3: Braking resistor connection 8/+R, 9/–R and PE connection, separable

[7] Electronics shield clamp and PE connection

[8] X2: Motor connection 4/U, 5/V, 6/W and PE connection, separable

[9] X17: Electronics terminal strip for safety contacts for safe stop

[10] X10: Electronics terminal strip for binary outputs and TF/TH input

[11] X16: Electronics terminal strip for binary inputs and outputs

[12] X13: Electronics terminal strip for binary inputs and RS485 interface

[13] X11: Electronics terminal strip for setpoint input AI1 and 10 V reference voltage

[14] X12: Electronics terminal strip for system bus (SBus)

[15] DIP switches S11 ... S14

[16] XT: Slot for DBG60B keypad or UWS21B serial interface

[17] 7-segment display

[18] Memory card

[1] X1: Power supply connection 1/L1, 2/L2, 3/L3

[2] X4: Connection for DC link connection –UZ +UZ and PE connection

[3] Memory card

[4] Fieldbus slot

[5] Expansion slot

[6] Encoder slot

[7] X3: Braking resistor connection 8/+R, 9/–R and PE connection

[8] Electronics shield clamp and PE connection

[9] X2: Motor connection 4/U, 5/V, 6/W

[10] X17: Electronics terminal strip for safety contacts for safe stop

[11] X10: Electronics terminal strip for binary outputs and TF/TH input

[12] X16: Electronics terminal strip for binary inputs and outputs

[13] X13: Electronics terminal strip for binary inputs and RS485 interface

[14] X11: Electronics terminal strip for setpoint input AI1 and 10 V reference voltage

[15] X12: Electronics terminal strip for system bus (SBus)

[16] DIP switches S11 ... S14