HoneywellEXPERION PKSSeries C I/O User's Guide EPDOC-X126-en-A November 2019

and regulations. The original TDC Basic Power Supplies do not support the UHIO CSA General

Purpose Certification.

CE Mark certification

The UHIO's CE Mark is only applicable for installations within Data Hiway (TDC 2000) cabinets with

the Series C Power supply SPS5792-142935 (HPN 51454517-100). It is assumed that the state of

as shipped and as first installed has been maintained for all applicable installations. For

installations that do not satisfy the previously mentioned conditions, the end user is responsible to

ensure that they conform to all applicable agency rules and regulations.

CC-HUIO12

The above constraints also apply to the CC-HUIO12 IOTA. Note that the CC-HUIO12 was tested

with TCB cable 51192054 only. Using the original TCB cable 30731611 with adaptor cable 51202979

may not pass CE Mark tests. For the conducted immunity test between 150kHZ and 250kHz, the AI

accuracy was 4.3% instead of its normal 0.1% at room temperature.

SERIES C I/O PLANNING AND DESIGN

This guide is intended to provide general information to assist you in planning and designing the

installation of your Experion Series C I/O.

l General Planning References

l Series C I/O and C300 topology

l Supported Series C I/O modules

l Supported Series C I/O options

l I/O Link performance specifications

l Universal Input/Output Module-2 (UIO-2)

3.1 General Planning References

Refer to the following documents for planning and design details for the Experion system in

general and the Fault Tolerant Ethernet supervisory network. For the sake of brevity, this Guide

does not repeat the applicable general guidelines, considerations, and cautions that are covered

in these other Guides.

l Control Hardware Planning Guide

l Server and Client Planning Guide

l Fault Tolerant Ethernet Overview and Implementation Guide

TIP

For complete Series C Control System Hardware Configuration planning information, refer

to the Control Hardware Planning Guide.

l Series C I/O appearance

l Series C I/O features

3.1.1 Series C I/O appearance

The layout of Series C components supports enhanced heat management and provides a 30%

reduction in overall size (space required to mount the hardware) versus the equivalent Process

Manger set.

3.1.2 Series C I/O features

The features of Series C I/O include:

l IO Module design - tilted 18 degrees off center:

o provides for better heat distribution

o allows for efficient field wiring

l Combination of I/O Module and Field terminations in the same area. The I/O Module is

mounted on the IOTA, which reduces cabinet space and eliminates items such as FTA

connection cables.

l Redundancy is done directly on the IOTA by simply adding a second IOM to the IOTA (with the

exception of the C300 controller).

For complete feature/functions for the following modules/IOTAs, refer to the Experion Series C

I/O Specifications document.

I/O

module/IOTA

Feature/function

Analog Input

w/HART

l Extensive self-diagnostics

l Optional redundancy

l HART capable, multi-variable instruments

l Fast (50ms) loop scan

l PV protection through a broken-wire detection diagnostic

l All channels configured for 4-20 mA inputs can detect broken

field wires. A soft failure alerts the maintenance staff for

corrective action.

l Non-incendive field power

l Non-incendive power for 4-20 mA loops is provided with no

external marshalling.

Analog Input

non-HART

l Extensive self-diagnostics

l Optional redundancy

l Fast (50ms) loop scan

l Non-incendive field power

Analog Output

w/HART

l Extensive self-diagnostics

l Optional redundancy

l HART capable, multivariable instruments

l Safe-state (FAILOPT) behaviors

l Each channel can be configured to HOLD, LAST, VALUE, or

SHED to a SAFE VALUE.

l Output read back checking of current delivered to the field

l PV protection through a broken-wire detection diagnostic

l Each channel can detect broken field wire. A soft failure alerts

the maintenance staff for corrective action.

l Non-incendive output

l No external marshalling required to support the 4-20ma loop,

and still provides for channel power protection.

Analog Output

non-HART

l Extensive self-diagnostics

l Optional redundancy

I/O

module/IOTA

Feature/function

l Safe-state (FAILOPT) behaviors

l Each channel can be configured to HOLD, LAST, VALUE, or

SHED to a SAFE VALUE.

l Output read back checking of current delivered to the field

l Non-incendive output

Digital Input

24VDC

l Extensive self-diagnostics

l IOM redundancy

l Input direct/reverse

l Internal or external field power selections

l Galvanic isolation

l PV protection through a broken-wire detection diagnostic

l Each channel can detect broken field wire. A soft failure alerts

the maintenance staff for corrective action.

l Non-incendive output

l No external marshalling required to support the 4-20ma loop,

and still provides for channel power protection.

Direct Input

High Voltage

l Extensive self-diagnostics

l Optional redundancy

l Input direct/reverse

l Galvanic isolation

Digital Input

High Voltage

PROX

l Extensive self-diagnostics

l Input direct/reverse

l Galvanic isolation

Direct Input -

Sequence of

Events

DI-SOE

l Extensive self-diagnostics

l Optional redundancy

l 1ms Sequence of Events for Discrete Inputs

l Low Latency / High Speed Scanning mode

l Broken wire detection

l Supplies non-incendive field power