HIMAHIMatrix Safety-Related Controller F31 03 Manual

For connecting a load to a 1-pole switching output, use the corresponding L- ground of 

the respective channel group (2-pole connection) to ensure that the internal protective 

circuit can function. 

nductive loads may be connected with no free-wheeling diode on the actuator. However, HIMA 

strongly recommends connecting a protective diode directly to the actuator.

Reaction in the Event of a Fault 

If the device detects a faulty signal on a digital output, the affected module output is set to the 

safe (de-energized) state using the safety switches. 

If a device fault occurs, all digital outputs are switched off. 

In both cases, the devices activates the FAULT LED. 

The error code allows the user to configure additional fault reactions in the user program. 

information on how to install, start up and configure the module in SILworX. 

1.1 Structure and Use of this Manual 

The content of this manual is part of the hardware description of the HIMatrix programmable 

electronic system. 

This manual is organized in the following main chapters: 

 Introduction 

 Safety 

 Product Description 

 Start-up 

 Operation 

 Maintenance 

 Decommissioning 

 Transport 

 Disposal 

Additionally, the following documents must be taken into account: 

Name Content Document number 

HIMatrix System Manual 

Compact Systems 

Hardware description of the HIMatrix 

compact systems 

HI 800 141 E 

HIMatrix Safety Manual Safety functions of the HIMatrix system HI 800 023 E 

HIMatrix Safety Manual for 

Railway Applications 

Safety functions of the HIMatrix system 

using the HIMatrix in railway 

applications 

HI 800 437 E 

SILworX Communication 

Manual 

Description of the communication 

protocols, ComUserTask and their 

configuration in SILworX 

HI 801 101 E 

SILworX Online Help Instructions on how to use SILworX - 

SILworX First Steps Introduction to SILworX using the 

HIMax system as an example 

HI 801 103 E 

Table 1: Additional Relevant Documents 

The latest manuals can be downloaded from the HIMA website at www.hima.com. The revision 

index on the footer can be used to compare the current version of existing manuals with the 

Internet edition. 

1.2 Target Audience 

This document addresses system planners, configuration engineers, programmers of 

automation devices and personnel authorized to implement, operate and maintain the modules 

and systems. Specialized knowledge of safety-related automation systems is required

1.3 Formatting Conventions 

To ensure improved readability and comprehensibility, the following fonts are used in this 

document: 

Bold To highlight important parts. 

Names of buttons, menu functions and tabs that can be clicked and used 

in the programming tool. 

Italics For parameters and system variables 

Courier Literal user inputs 

RUN Operating state are designated by capitals 

Chapter 1.2.3 Cross references are hyperlinks even though they are not particularly 

marked. When the cursor hovers over a hyperlink, it changes its shape. 

Click the hyperlink to jump to the corresponding position. 

Safety notes and operating tips are particularly marked. 

1.3.1 Safety Notes 

The safety notes are represented as described below. 

These notes must absolutely be observed to reduce the risk to a minimum. The content is 

structured as follows: 

 Signal word: warning, caution, notice 

 Type and source of risk 

 Consequences arising from non-observance 

 Risk prevention 

Type and source of risk! 

Consequences arising from non-observance 

Risk prevention 

The signal words have the following meanings: 

 Warning indicates hazardous situation which, if not avoided, could result in death or serious 

injury. 

 Caution indicates hazardous situation which, if not avoided, could result in minor or modest 

injury. 

 Notice indicates a hazardous situation which, if not avoided, could result in property damage

Type and source of damage! 

Damage prevention 

Safety 

All safety information, notes and instructions specified in this document must be strictly 

observed. The product may only be used if all guidelines and safety instructions are adhered to. 

This product is operated with SELV or PELV. No imminent risk results from the product itself. 

The use in Ex-Zone is permitted if additional measures are taken. 

2.1 Intended Use 

HIMatrix components are designed for assembling safety-related controller systems. 

When using the components in the HIMatrix system, comply with the following general 

requirements. 

Environmental Requirements 

Requirement type Range of values 

Protection class Protection class III in accordance with IEC/EN 61131-2 

Ambient temperature 0...+60 °C 

Storage temperature -40...+85 °C 

Pollution Pollution degree II in accordance with IEC/EN 61131-2